P0572 – Brake Switch A Circuit Low (Ford F-150)

Ford logoFord-specific code — factory diagnostic data
DTC Data Sheet
CodeP0572
Vehicle2011 Ford F-150
ModulePCM
Fault typeCircuit Low
Official meaningBrake Switch A Circuit Low

Definition source: Ford factory description. Diagnostic guidance is based on factory-defined fault logic for this code.

🔍Decode any Ford F-150 VIN — free recalls, specs & safety ratings — free VIN decoder with NHTSA data

⚠ Scan tool requirement: This is a Ford-specific code. A generic OBD2 reader will retrieve the code but cannot access the module-level data, live PIDs, or bi-directional tests needed for diagnosis. A professional-grade scan tool with Ford coverage is required for complete diagnosis.

↗Looking for the cross-vehicle definition? Read the generic P0572 article for the SAE-defined fault logic that applies to all manufacturers.

P0572 Quick Answer

P0572 on a 2011 F-150: Brake Switch A Circuit Low. Ford’s factory diagnostic guidance for this code: REFER to CRUISE CONTROL .

What Does P0572 Mean on a 2011 F-150?

The 2011 Ford F-150 uses the PCM to monitor and diagnose this circuit. P0572 is set when the module detects brake switch a circuit low. The official meaning per the 2011 F-150 service information is exactly: Brake Switch A Circuit Low.

Symptoms

  • Check engine light or system warning indicator on the instrument cluster
  • Reduced functionality of the affected pcm system
  • Possible co-codes from connected modules on the 2011 F-150 CAN bus (HS-CAN/MS-CAN)

Common Causes

  • Fault in the named component, sensor, or actuator circuit
  • Open or shorted wiring in the affected circuit
  • Connector corrosion or backed-out terminal
  • Loss of supply voltage or ground at the affected device
  • Module internal fault (rare — verify wiring and supplies first)

Ford-Recommended Diagnostic Action

Per the 2011 Ford F-150 service information for P0572:

REFER to CRUISE CONTROL .

Pinpoint test references above are Ford F-150 service-manual chart numbers. Refer to the corresponding chart in the Ford 2011 F-150 Workshop Manual for step-by-step diagnostic procedures.

Diagnostic Approach

For P0572 on the 2011 Ford F-150 you’ll need a bidirectional scan tool capable of reading PCM live data and freeze frame, a digital multimeter, and the 2011 Ford F-150 PCM wiring diagram.

  1. Verify the code is current rather than just stored history. Use the scan tool’s self-test on the PCM.
  2. Read freeze-frame data and any related codes. Modules sharing CAN bus segments often log overlapping faults.
  3. Inspect the connector at the device named in the code description. Wiggle-test the connector while monitoring live data to expose intermittent faults.
  4. Measure supply voltage and ground integrity at the affected device with the engine running.
  5. Follow the Ford-recommended action above — including any pinpoint-test reference — for procedure-level diagnosis.
  6. If supplies are clean and the connector is sound, isolate the device with a known-good substitute. Re-clear the code and verify it does not return on a road test.

Possible Fixes

  • Replace the failed device or sensor identified during diagnosis
  • Repair open or shorted wiring
  • Connector pin-tension or pigtail repair
  • Module replacement and PMI (Programmable Module Installation) if the module itself is faulty

Can I Still Drive With P0572?

Drivability impact depends on the affected subsystem. PCM faults that affect a primary safety system (brakes, restraints, steering) should be repaired before further driving. Comfort or convenience faults can usually be deferred briefly without immediate safety risk.

Compare nearby Ford brake switch trouble codes with similar definitions, fault patterns, and diagnostic paths.

  • B00DF – 13 – Passenger Restraints Disable Switch: Incorrect Component Installed (Ford F-150)
  • P1700 – Transmission Indeterminate Failure (failed To Neutral) (Ford F-150)
  • P1702 – Transmission Range Sensor Circuit Intermittent: No Sub Type Information (Ford F-150)
  • P1705 – Tr Sensor Circuit Did Not Indicate Park/neutral During The Self-test. (Ford F-150)
  • P1711 – Tft Sensor Out Of Self-test Range (Ford F-150)
  • P1744 – Torque Converter Clutch Solenoid Circuit Performance (Ford F-150)

FAQ

Will P0572 clear itself on a Ford F-150?

If the underlying fault was a momentary glitch — for example a brief connector dropout or a one-time low-voltage event — the P0572 may clear after a few drive cycles. Persistent root causes (failed device, broken wire, corroded terminal) will keep the fault active until the affected component is repaired on the Ford F-150.

Can I drive my Ford F-150 with P0572 active?

It depends which subsystem is affected. If the P0572 is in a primary safety system (brakes, restraints, steering, air suspension), the Ford F-150 should be driven only to a workshop. Comfort, lighting, and audio faults are lower priority but still worth addressing — the Ford F-150’s CAN architecture means a single unresolved code can mask others.

How much does it cost to fix P0572 on a Ford F-150?

Repair cost depends on the named device. On the Ford F-150, simple connector or wiring repairs typically run $80-200 in shop labour. Sensor replacements run $120-450 including parts and diagnostic time. Module replacement (when the affected control module itself has failed) is the most expensive path at $400-1,200 depending on whether the new module needs programming. Get a written estimate that breaks out diagnosis time, parts, and any required PMI / programming charge.

What does the official Ford F-150 service definition say about P0572?

Per the factory service information, P0572 is defined as: Brake Switch A Circuit Low. The diagnostic procedure is in the Ford F-150 service-manual chapter for the affected module.