Ford-specific code — factory diagnostic data| DTC Data Sheet | |
| Code | B1168 |
| Vehicle | 2011 Ford F-150 |
| Module | POWER RUNNING BOARD (PRB) MODULE |
| Fault type | Short |
| Official meaning | Left Power Running Board Stow Circuit Short To Ground |
Definition source: Ford factory description. Diagnostic guidance is based on factory-defined fault logic for this code.
Decode any Ford F-150 VIN — free recalls, specs & safety ratings — free VIN decoder with NHTSA data
B1168 Quick Answer
B1168 on a 2011 F-150: Left Power Running Board Stow Circuit Short To Ground. Ford’s factory diagnostic guidance for this code: GO to PINPOINT TEST D .
What Does B1168 Mean on a 2011 F-150?
The 2011 Ford F-150 uses the POWER RUNNING BOARD (PRB) MODULE to monitor and diagnose this circuit. B1168 is set when the module detects left power running board stow circuit short to ground. The official meaning per the 2011 F-150 service information is exactly: Left Power Running Board Stow Circuit Short To Ground.
Symptoms
- Check engine light or system warning indicator on the instrument cluster
- Reduced functionality of the affected power running board (prb) module system
- Possible co-codes from connected modules on the 2011 F-150 CAN bus (HS-CAN/MS-CAN)
Common Causes
- Fault in the named component, sensor, or actuator circuit
- Open or shorted wiring in the affected circuit
- Connector corrosion or backed-out terminal
- Loss of supply voltage or ground at the affected device
- Module internal fault (rare — verify wiring and supplies first)
Ford-Recommended Diagnostic Action
Per the 2011 Ford F-150 service information for B1168:
GO to PINPOINT TEST D .
Pinpoint test references above are Ford F-150 service-manual chart numbers. Refer to the corresponding chart in the Ford 2011 F-150 Workshop Manual for step-by-step diagnostic procedures.
Diagnostic Approach
For B1168 on the 2011 Ford F-150 you’ll need a scan tool that reads the PRB module on the 2011 F-150 (running-board option), plus a digital multimeter.
- Verify the code is current rather than just stored history. Use the scan tool’s self-test on the POWER RUNNING BOARD (PRB) MODULE.
- Read freeze-frame data and any related codes. Modules sharing CAN bus segments often log overlapping faults.
- Inspect the connector at the device named in the code description. Wiggle-test the connector while monitoring live data to expose intermittent faults.
- Measure supply voltage and ground integrity at the affected device with the engine running.
- Follow the Ford-recommended action above — including any pinpoint-test reference — for procedure-level diagnosis.
- If supplies are clean and the connector is sound, isolate the device with a known-good substitute. Re-clear the code and verify it does not return on a road test.
Possible Fixes
- Replace the failed device or sensor identified during diagnosis
- Repair open or shorted wiring
- Connector pin-tension or pigtail repair
- Module replacement and PMI (Programmable Module Installation) if the module itself is faulty
Can I Still Drive With B1168?
Drivability impact depends on the affected subsystem. POWER RUNNING BOARD (PRB) MODULE faults that affect a primary safety system (brakes, restraints, steering) should be repaired before further driving. Comfort or convenience faults can usually be deferred briefly without immediate safety risk.
FAQ
Will B1168 clear itself on a Ford F-150?
If the underlying fault was a momentary glitch — for example a brief connector dropout or a one-time low-voltage event — the B1168 may clear after a few drive cycles. Persistent root causes (failed device, broken wire, corroded terminal) will keep the fault active until the affected component is repaired on the Ford F-150.
Can I drive my Ford F-150 with B1168 active?
It depends which subsystem is affected. If the B1168 is in a primary safety system (brakes, restraints, steering, air suspension), the Ford F-150 should be driven only to a workshop. Comfort, lighting, and audio faults are lower priority but still worth addressing — the Ford F-150’s CAN architecture means a single unresolved code can mask others.
How much does it cost to fix B1168 on a Ford F-150?
Repair cost depends on the named device. On the Ford F-150, simple connector or wiring repairs typically run $80-200 in shop labour. Sensor replacements run $120-450 including parts and diagnostic time. Module replacement (when the affected control module itself has failed) is the most expensive path at $400-1,200 depending on whether the new module needs programming. Get a written estimate that breaks out diagnosis time, parts, and any required PMI / programming charge.
What does the official Ford F-150 service definition say about B1168?
Per the factory service information, B1168 is defined as: Left Power Running Board Stow Circuit Short To Ground. The diagnostic procedure is in the Ford F-150 service-manual chapter for the affected module.