Toyota-specific code — factory diagnostic data| DTC Data Sheet | |
| Code | C1408 |
| Vehicle | 2014 Toyota Highlander (XU50) |
| System | Vehicle Stability Control System |
| Fault type | Circuit Open |
| Official meaning | Open or Short in Rear Speed Sensor LH Circuit |
| Source | 2014 Toyota Highlander factory diagnostic information |
Definition source: Toyota factory description. Diagnostic guidance is based on factory-defined fault logic for this code.
C1408 on the 2014 Toyota Highlander means: Open or Short in Rear Speed Sensor LH Circuit. It is a circuit open code reported by the Vehicle Stability Control System.
Decode any Toyota Highlander VIN — free recalls, specs & safety ratings — free VIN decoder with NHTSA data
C1408 Quick Answer
C1408 on a 2014 Toyota Highlander indicates Open or Short in Rear Speed Sensor LH Circuit. Start with a freeze-frame check and a careful inspection of the connector and wiring at the affected device before replacing any parts.
What Does C1408 Mean on a Toyota Highlander?
On the 2014 Toyota Highlander, the Vehicle Stability Control System sets C1408 when it detects a fault matching its official definition: Open or Short in Rear Speed Sensor LH Circuit. This is a manufacturer-specific definition from Toyota factory diagnostic data and applies to the XU50-generation Highlander.
Symptoms
- Warning light for the affected system (check engine, ABS, airbag, or a system indicator depending on the module)
- Reduced or lost function of the vehicle stability control system
- Possible related codes from other modules on the Highlander CAN/LIN network
Common Causes
- Fault in the component named in the definition (open or short in rear speed sensor lh circuit)
- Open, shorted, or high-resistance wiring in the affected circuit
- Connector corrosion, water ingress, or a backed-out terminal
- Loss of supply voltage or a poor ground at the device
- Module internal fault — confirm wiring and supplies before condemning the module
Diagnostic Approach
For C1408 on the 2014 Toyota Highlander you’ll want a scan tool with Toyota-enhanced coverage (Techstream-class) — generic OBD-II readers usually will not read C-codes — plus a digital multimeter and the wiring diagram.
- Confirm the code is current, not stored history, and record freeze-frame data.
- Read all modules — related codes often pinpoint the root cause faster than the headline code.
- Inspect and wiggle-test the connector at the named device while watching live data.
- Measure supply voltage and ground integrity at the device; verify the circuit against the Highlander wiring diagram.
- Substitute or isolate the suspect device only after wiring and supplies check out.
- Clear the code and road-test through one or two drive cycles to confirm the repair.
Possible Fixes
- Repair open/short/high-resistance wiring or a corroded connector
- Restore supply voltage or ground at the affected device
- Replace the failed component named in the definition
- Replace and, where required, initialise/program the module if it is internally faulty
Can I Still Drive With C1408?
It depends on the system. Vehicle Stability Control System faults that affect braking, the airbag/restraint system, power steering, or stability control should be repaired before further driving. Comfort or convenience faults can usually be deferred briefly, but related codes can mask one another on the Highlander network — diagnose promptly.
FAQ
Is C1408 specific to the Toyota Highlander?
The definition here is taken from 2014 Toyota Highlander (XU50) factory diagnostic data. The same code may appear on other Toyota models, but the affected module and exact criteria can differ between platforms.
Can I clear C1408 without fixing it?
You can clear it, but if the underlying fault is still present the Highlander will reset the code on the next drive cycle that runs the relevant monitor. Diagnose the cause first.
Will a generic OBD-II reader show C1408?
Often not — C-codes are manufacturer-specific and usually require a scan tool with Toyota-enhanced coverage such as a Techstream-class tool.
Source
Code definition from 2014 Toyota Highlander (XU50) factory diagnostic information (Vehicle Stability Control System). Symptom, cause, and diagnosis guidance summarised from standard OBD-II diagnostic practice for this platform.