Toyota-specific code — factory diagnostic data| DTC Data Sheet | |
| Code | P1603 |
| Vehicle | 2014 Toyota Sequoia (XK60) |
| System | SFI System |
| Fault type | Fault |
| Official meaning | Engine Stall History |
| Source | 2014 Toyota Sequoia factory diagnostic information |
Definition source: Toyota factory description. Diagnostic guidance is based on factory-defined fault logic for this code.
P1603 on the 2014 Toyota Sequoia means: Engine Stall History. It is a fault code reported by the SFI System.
Decode any Toyota Sequoia VIN — free recalls, specs & safety ratings — free VIN decoder with NHTSA data
P1603 Quick Answer
P1603 on a 2014 Toyota Sequoia indicates Engine Stall History. Start with a freeze-frame check and a careful inspection of the connector and wiring at the affected device before replacing any parts.
What Does P1603 Mean on a Toyota Sequoia?
On the 2014 Toyota Sequoia, the SFI System sets P1603 when it detects a fault matching its official definition: Engine Stall History. This is a manufacturer-specific definition from Toyota factory diagnostic data and applies to the XK60-generation Sequoia.
Symptoms
- Warning light for the affected system (check engine, ABS, airbag, or a system indicator depending on the module)
- Reduced or lost function of the sfi system
- Possible related codes from other modules on the Sequoia CAN/LIN network
Common Causes
- Fault in the component named in the definition (engine stall history)
- Open, shorted, or high-resistance wiring in the affected circuit
- Connector corrosion, water ingress, or a backed-out terminal
- Loss of supply voltage or a poor ground at the device
- Module internal fault — confirm wiring and supplies before condemning the module
Diagnostic Approach
For P1603 on the 2014 Toyota Sequoia you’ll want an OBD-II scan tool with live-data and freeze-frame support (a Toyota Techstream-class tool reads enhanced data), plus a digital multimeter and the wiring diagram.
- Confirm the code is current, not stored history, and record freeze-frame data.
- Read all modules — related codes often pinpoint the root cause faster than the headline code.
- Inspect and wiggle-test the connector at the named device while watching live data.
- Measure supply voltage and ground integrity at the device; verify the circuit against the Sequoia wiring diagram.
- Substitute or isolate the suspect device only after wiring and supplies check out.
- Clear the code and road-test through one or two drive cycles to confirm the repair.
Possible Fixes
- Repair open/short/high-resistance wiring or a corroded connector
- Restore supply voltage or ground at the affected device
- Replace the failed component named in the definition
- Replace and, where required, initialise/program the module if it is internally faulty
Can I Still Drive With P1603?
It depends on the system. SFI System faults that affect braking, the airbag/restraint system, power steering, or stability control should be repaired before further driving. Comfort or convenience faults can usually be deferred briefly, but related codes can mask one another on the Sequoia network — diagnose promptly.
FAQ
Is P1603 specific to the Toyota Sequoia?
The definition here is taken from 2014 Toyota Sequoia (XK60) factory diagnostic data. The same code may appear on other Toyota models, but the affected module and exact criteria can differ between platforms.
Can I clear P1603 without fixing it?
You can clear it, but if the underlying fault is still present the Sequoia will reset the code on the next drive cycle that runs the relevant monitor. Diagnose the cause first.
Will a generic OBD-II reader show P1603?
Most generic readers show powertrain (P) codes, but Toyota-enhanced data (e.g. a Techstream-class tool) gives the full freeze-frame and live data needed to diagnose it properly.
Source
Code definition from 2014 Toyota Sequoia (XK60) factory diagnostic information (SFI System). Symptom, cause, and diagnosis guidance summarised from standard OBD-II diagnostic practice for this platform.